|
Publications
|
| Abbaszadeh, P., Kheirandish, S., Saghafian, H., Goodarzy, M.H., "Effect of austenitizing temperature on mechanical properties of the mixed bainite - Martensite microstructure in CrMoV steel", Materials Research, 21(1),e20170469, 2018 |
|
Nikbakht, R., Seyedein, S.H., Kheirandish, S., Assadi, H., Jodoin, B., "Asymmetrical bonding in cold spraying of dissimilar materials", Applied Surface Science, Volume 444, 30 June 2018, Pages 621-632
|
|
Nouri, A., Kheirandish, S., Saghafian, H., "A Study of Redistribution of Silicon in Dual-Phase Silicon Steels", Metal Science and Heat Treatment, Volume 59, Issue 9-10, 1 January 2018, Pages 569-574
|
| Abazari, S., Rastegari, S., Kheirandish, S., "Influence of Pulse Electrodeposition and Heat Treatment on Microstructure, Tribological, and Corrosion Behavior of Nano-Grain Size Co-W Coatings", Journal of Materials Engineering and Performance, Volume 26, Issue 7, 1 July 2017, Pages 3133-3143 |
| Mahmoudiniya, M., Kheirandish, S., Asadiasadabad, M., "The Effect of Cold Rolling on Microstructure and Mechanical Properties of a New Cr–Mn Austenitic Stainless Steel in Comparison with AISI 316 Stainless Steel", Transactions of the Indian Institute of Metals, Volume 70, Issue 5, 1 July 2017, Pages 1251-1259 |
|
Mirzakouchakshirazi, H., Eivani, A.R.,Kheirandish, S., "Effect of post-deformation annealing treatment on interface properties and shear bond strength of Al-Cu bimetallic rods produced by equal channel angular pressing", Iranian Journal of Materials Science and Engineering, Volume 14, Issue 4, December 2017, Pages 25-34
|
| Seifollahi, M., Sahrapour, P., Abbasi, S.M., Kheirandish, S., Razavi, S.H., "Mathematical-Thermodynamic Prediction and Kinetics of Eta Phase Formation in Fe–Ni-Based Superalloys", Transactions of the Indian Institute of Metals, 19 May 2017, Pages 1-6 |
| Seifollahi, M., Razavi, S.H., Kheirandish, S., Abbasi, S.M., "Effect of minor Zr addition on γ′ and η phase precipitation and tensile properties of A286 superalloy", Indian Journal of Engineering and Materials Sciences, Open Access Volume 24, Issue 2, April 2017, Pages 147-152 |
|
Mahmoudiniya. M., Kheirandish, S., Asadi Asadabad, M., "High temperature tensile properties of new Fe-Cr-Mn developed steel", Iranian Journal of Materials Science and Engineering, Volume 14, Issue 1, March 2017, Pages 47-57
|
| Karimi, A., Kheirandish, S., Mahmoudiniya, M., "Effect of bainite volume fraction on mechanical properties of a ferrite-bainite-martensite steel", Kovove Materialy, Volume 55, Issue 3, 2017, Pages 175-182 |
| Nayebpashaee, N., Vafaeenezhad, H., Kheirandish, S., Soltanieh, M., "Experimental and numerical study on plasma nitriding of AISI P20 mold steel",International Journal of Minerals, Metallurgy and Materials, Volume 23, Issue 9, 1 September 2016, Pages 1065-1075 |
Karami, S., Jafarian, H. , Eivani, A.R., Kheirandish, S., "Engineering tensile properties by controlling welding parameters and microstructure in a mild steel processed by friction stir welding", Materials Science and Engineering A, Volume 670, 18 July 2016, Pages 68-74 |
| Nayebpashaee, N., Soltanieh, M.,Kheirandish, Sh., "A Study on Formation and Growth Mechanism of Nitride Layers during Plasma Nitriding Process of Plastic Injection Mold Steel", Materials and Manufacturing ProcessesVolume 31, Issue 9, 3 July 2016, Pages 1192-1200 |
| Alabbasian, F., Boutorabi, S.M.A., Kheirandish, S., "Effect of inoculation and casting modulus on the microstructure and mechanical properties of ductile Ni-resist cast iron", Materials Science and Engineering AVolume 651, January 10, 2016, Pages 467-473 |
| Shirazi, H., Kheirandish, S., Safarkhanian, M.A., "Effect of process parameters on the macrostructure and defect formation in friction stir lap welding of AA5456 aluminum alloy", Measurement: Journal of the International Measurement Confederation, Volume 76, 12 December 2015, Pages 62-69 |
|
Mohammad Momeni, Shahram Kheirandish , Hasan Saghafian, Jalal Hedjazi , Mansour Momeni, "Effects of heat treatments on mechanical properties of modified cast B D3 tool steel", Materials and Design, 54(2014)742-747.
|
|
M.Seifollahi, Sh. Kheirandish, S.H.Razavi, S.M.Abbasi ,"The precipitation of η phase in an Fe-Ni-based superalloy with different Ti/Al ratios", International Journal of Materials Research,104( 2013)4 pp. 344-350.
|
|
Hamed Sabet, Shamsedin Mirdamadi, Shahram Kheirandish, Masoud Goodarzi, "EFFECT OF VOLUME FRACTION OF (Cr,Fe)7C3 CARBIDES ON CORROSION RESISTANCE OF THE Fe-Cr-C HARDFACING ALLOYS AT C/Cr =6", Metall. Mater. Eng. Vol 19 (2) 2013 pp. 107-114.
|
|
M.Seifollahi, Sh. Kheirandish, S.H.Razavi, S.M.Abbasi, P.Sahrapour , " Effect of eta phase on mechanical properties of A286 superalloy using shear punch testing", ISIJ International, Vol. 53 (2013), No. 2, pp. 311–316.
|
|
Payam Abdollahi, Alborz Amirsadeghi, Shahram Kheirandish, Shamsoddin Mirdamadi, "Formation Kineticks of austenite in pearlitic ductile iron", International J of Mineral Metallurgy and materials vol.19 no.6, 2012, pp. 506-510.
|
| A. Anazadeh Sayed, Sh. Kheirandish, " Effect of the tempering temperature on the microstructure and mechanical properties of dual phase steels", Materials Science and Engineering A, 2011 |
| M. Morakabati, M. Aboutalebi, Sh. Kheirandish, A. Karimi Taheri, S.M. Abbasi, "High temperature deformation and processing map of a NiTi intermetallic alloy", Intermetallics, 19 (2011) 1399-1404. |
|
M. Morakabati, M. Aboutalebi, Sh. Kheirandish, A. Karimi Taheri, S. M. Abbasi, "Hot tensile properties and microstructural evolution of NiTi and NiTiCu shape memory alloys", Materials and Design 32 (2011) 406–413
|
|
H. Sabet , Sh. Khierandish, Sh. Mirdamadi, M. Goodarzi "The Microstructure and Abrasive Wear Resistance of Fe–Cr–C Hardfacing Alloys with the Composition of Hypoeutectic, Eutectic, and Hypereutectic at Cr/C = 6", Tribol Lett, vol. 44 , 2011, pp.237–245.
|
|
M Morakabati, Sh. Kheirandish, M.R. Aboutalebi, A. KarimiTaheri, S.M. Abbasi, " A study on the hot workability of wrought NiTi shape memory alloy", Materials Science and Engineering A, 528(2011), pp. 5656–5663.
|
| A. Noorian, Sh. Kheirandish, H. Saghafian, "Evaluation of the mechanical properties of niobium modified cast AISI H 13 hot work tool steel", IJMSE, Vol 7, No. 2, 2010, pp. 22-29. |
| M. Morakabati, Sh Kheirandish, M. Aboutalebi, A. Karimi Taheri, S. M. Abbasi, "The effect of Cu addition on the hot deformation of NiTi shape memory alloys", Journal of Alloys and Compounds, 499 (2010) 57-62 |
| H.R. Abedi, A. Fareghi, H. Saghafian. Sh. Kheirandish, "Sliding wear behavior of a ferritic pearlitic ductile cast iron with different nodule count", Wear, 268 (2010) 622-628. |
| Sh. Kheirandish , H. Saghafian, J. Hedjazi, M. Momeni, "Effects of heat treatment on microstructure of modified cast AISI D3 cold work tool steel'', Journal of Iron and Steel Research International, 17 (2010) 40-45. |
| M. Asadi Asadabad, Sh. Kheirandish, Abdoljavad Novinrooz, "Tempering behavior of 4.5%Cr-2%W-0.25%V steel", Iron and Steel Research International, 17 (2010) 57-62. |
| Mohsen Asadi Asadabad, Shahram Kheirandish, Abdoljavad Novinrooz, " Microstructural and mechanical behavior of Cr-W-V steel", Materials Science and Engineering A 527, 2010, pp. 1612-1616 |
| A. Nouri, H. Saghafian, Sh. Kheirandish, "Effect of Silicon content and intercritical annealing on the Manganese partitioning in the dual-phase steels", Journal of Iron and Steel Research International 17(5), 2010, pp. 46-51. |
| A. Nouri, H.Saghafian, Sh. Kheirandish, "Influence of volume fraction of martensite on the work hardening behaviour of two dual-phase steels with high and low silicon", International Journal of Material Research, 101 (2010), 1286-1292. |
| M. Abbasi, Sh. Kheirandish, Y. Kharrazi, and J. Hejazi, "Tribological Studies of Steels Using the Abrasive Wheel" Advanced Material Research, Vol.83-86, 2010, pp. 545-552 |
| Majid Abbasi, Shahram Kheirandish, Yosef Kharrazi, Jalal Hejazi, "On the comparison of the abrasive wear behavior of aluminum alloyed and standard Hadfield steels", WEAR,267, 2010, pp. 202-207. |
| M. Abbasi, Sh. Kheirandish, Y. Kharrazi, J. Hejazi, "The fracture and plastic deformation of Aluminum alloyed Hasfield steel", Materials Science and Enginnering A 513-514, 2009, pp. 72-76 |
| M. Asadi Asadabad, Sh. Kheirandish, Abdoljavad Novinrooz, "Identification of Nanometric carbide precipitates in Fe-Cr-W-V system", Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry,Vol. 39, 2009, pp. 322-326 |
| H. Mohamadzade, Sh. Kheirandish, H. Saghafian, "Effect of graphite flakes on the microstructure of melted, transition and heat affected zones in grey cast iron re-melted by TIG", IJSME, Vol. 6, No. 2, 2009. |
| H. Mohamadzade, Sh. Kheirandish, H. Saghafian, "Sliding wear behaviour of gray cast iron surface remelted by TIG", accepted for JMST Journal, 2009 |
| M.M. Karimi, Sh. Kheriandish, " Comparison of work hardening behaviour of ferritic-bainitic and ferritic-matensitic dual phase steels" Steel Research International Journal, Vol. 80, No. 2, 2009, pp. 160-164 |
| A. Nouri, Sh. Kheirandish, H. Saghafian, "Effect of Silicon content on the strain hardening of dual-phase steels", IJMSE, Vol. 5, No. 4, 2008, pp. 40-49 |
| V. Abouei, H. Saghafian, Sh. Kheirandish, Kh. Ranjbar, " An investigation of the wear behaviour of 0.2% C dual phase steel", Journal of Materials Processing Technology, Vol. 203, July 2008, pp. 107-112 |
| Sh. Kheirandish, A. Noorian, "Effect of niobium on microstructure of cast AISI H13 hot work tool stee", Journal of Iron and Steel Research International, Vol. 15, July 2008, pp. 61-67 |
| F. Nikoosohbat, SH. Kheirandish, M. Goodarzi, M. Pouranvari, P. Marashi, "Failure behavior of Resistance Spot Welded DP980 Steel", Science and Technology of Welding and Joining, accepted for publication 2008 |
| M. Asadi, M. Goodarzi, S. Kheirandish," Kinetics of austenite formation in dual phase steels", ISIJ Journal, Vol. 48, No. 9, 2008, pp. 1251-1255 |
|
V. Abouie, H. Saghafian , Sh. Kheirandish, “Effect of microstructure on the oxidative wear behaviour of plan Carbon steel”, Wear, Vol. 262, 2007, pp. 1225-1231
|
|
V. Abouei, H. Saghafian, Sh. Kheirandish, “Dry sliding oxidative wear in plain carbon dual phase steel”, Journal of Iron & Steel Research International, No. 4, Vol. 14, 2007, pp. 43-48
|
|
V. Abouie, H. Saghafian, Sh. Kheirandish, Kh. Ranjbar, “Mild oxidative wear behaviour of plain carbon dual-phase steel”, Steel Research International, 2007, pp. 506-511
|
|
V. Abouie, H. Saghafian, Sh. Kheirandish, Kh. Ranjbar, “A study on the wear behaviour of dual phase steel”, Journal of Materials Science & Technology, Vol. 23, No. 01, 2007, pp. 107-110
|
|
H. Saghafian, Sh. Kheirandish, “Correlating microstructural features with wear resistance of dual phase steel”, Materials Letters, 2007, pp. 3059-3063
|
|
Sh. Kheirandish, “Modification of NbC with Ti in cast Nb tool steel”, International Journal of Engineering, Vol. 14, No. 2, Spring 2003, pp. 89-99
|
|
Jafari, R., Kheirandish, S., Mirdamadi, S, "Effect of Q&P heat treatment on fine microstructure and mechanical properties of a low-alloy medium-carbon steel",AIP Conference ProceedingsVolume 1920, 10 January 2018, Article number 0200306th International Biennial Conference on UltraFine Grained and Nanostructured Materials, UFGNSM 2017; Kish Island; Iran; 12 November 2017 through 13 November 2017; Code 133475
|
| M. Asadi Asadabad, Sh. Kheirandish, Abdul Javad Novinrooz, "Formation of Nano Carbides in Fe-Cr-W-V , 2nd Iran-India Joint conference on Nanotechnologhy", Iranian Nano Technology Initiative, University of Isfshan, 5-7 May 2009 |
|
M. Abbasi, Sh. Kheirandish, Y. Kharrazi, J. Hejazi, "Tribological Studies of Steels Using the Abrasive wheel", Proc. of Con. AMPT 2008,The International Conference on Advances in Materials and Processing Technologies, 2-5 November, Manama, kingdom of Bahrain
|
| A. Jafarigol, Sh. Kheirandish, " Surface austempering of medium carbon steel", Proc. of Con. European metallurgical conference 2007, 11-14 June 2007, Duesseldorf, Germany |
Educational Records
|
Degree
|
Major
|
Year of Graduation
|
University
|
Location
|
|
B.Sc.
|
Metallurgical EngineerinOKg
|
1977
|
Iran University of Science and Technology
|
Iran
|
|
M.Sc.
|
Materials Science Engineering
|
1987
|
Sharif University of Technology
|
Iran
|
|
Ph.D
|
Materials Science Engineering
|
1996
|
Iran University of Science and Technology
|
Iran
|
Teaching Experiences:
- Physical Metallurgy
- Phase Transformation
- Heat Treatment
- Special Topics
|
Book's Name
|
Authors' Name
|
Date
|
|
Tool Steels
|
Kheirandish, Adeli, Asadi,....
|
|
Conference Organizer:
13th Iranian Foundrymen Society Seminar, Tehran, Iran, 2001
|
/khairandish.jpg)
